• 济南慧杭门业有限责任公司
  • 联系人:张经理
  • 手机:15966334566
  • 地址:济南市工业南路106号
  • 网址:http://www.jnjqjc.com
新闻中心当前位置:首页-新闻中心
    分享济南玻璃门安装的四点注意事项
    来源:http://www.jnjqjc.com   时间:2016-3-29 11:42:19
    分享济南玻璃门安装的四点注意事项
    The four precautions share jinan glass door installation
    1、门扇安装前,地面地弹簧与门框顶面的定位销应定位安装完毕,两者必须同轴线。安装时用吊垂线检查,确保地弹簧转轴与定位销的中心线在同一垂直线上。济南玻璃
    1, door leaf before installation, the ground floor spring with the dowel pin frame roof should be installed, both must coaxial line. When installation with vertical inspection, to ensure that the floor spring shaft and positioning pin center line on the same vertical line.
    2、门扇定位安装:先将门框横梁上的定位销用本身的调节螺钉调出横梁平面2mm;再玻璃门扇竖起来,把门扇下门夹内的转动销连接件的孔位对准地弹簧的转动销轴,并转动门扇将孔位套入销轴上;
    2, door leaf positioning installation: first the locating pin on the frame beam with itself out of the adjustable screw bar planar 2 mm; Glass door leaf stand up again, the rotation of the door leaf door folder pin connector of the rotation of the spring pin hole position alignment, and the number of the rotating door leaf will set into the pin shaft;
    然后把门扇转动90度使之与门框横梁成直角,把门扇上门夹中的转动连接件的孔对准门框横梁上的定位销,调节定位销的调节螺钉,将定位销插入孔内15mm左右。
    Then put the door leaf turn 90 degrees at right angles to the frame beam, the door leaf turn the fitting of a hole in the door clip on the door frame beam positioning pin, adjust the adjusting screw of positioning pin, insert the dowel pin hole around 15 mm.
    3、安装玻璃门扇上下门夹:把上下金属门夹分别装在玻璃门扇下下两端,并测量门扇高度。如果门扇的上下边距门横框及地面的缝隙超过规定值,即门扇高度不够,可在上下门夹内的玻璃底部垫木夹板条。门扇的大小需要根据实际情况来定。
    3, install glass door leaf and the door: the upper and lower metal door clamp respectively installed on both ends of the glass doors down, and the door leaf height measurement. If the doors on bottom margin the door frame and ground cracks more than specified value, namely the door leaf height is insufficient, can be in the up and down the door at the bottom of the glass mat wood plywood. The size of the door leaf need according to the actual situation to decide.
    4、安装玻璃门拉手:全玻璃门扇上的拉手孔洞,一般在裁割玻璃时加工完成。拉手连接部分插入洞口时不能过紧,应略有松动;如插入过松,可在插入部分裹上软质胶带。安装前在拉手插入玻璃的部分涂上少许玻璃胶。
    4, glass door shake handshandle installation: the whole handle holes on the glass door leaf, are usually performed at the time of cut glass processing. Shake handshandle connection part when inserted into the hole not too close, should be slightly loose; Such as insert too loose, can be wrapped in soft adhesive tape in the insert part. Before the installation in the shake handshandle insert part of the glass coated with a little glass glue.
    5、固定玻璃门扇上下门夹:定好门扇高度后,在厚玻璃与金属上下门夹内的两侧缝隙处,同时插入小木条,轻敲稳实,然后在小木条、厚玻璃、门夹之间的缝隙中注入玻璃胶。
    5, fixed glass door leaf and door stopper: after good door leaf height, the thick glass and metal from top to bottom in aperture place on both sides of the door stopper, insert a board at the same time, tapping stable, then in a small wood, thick glass, door clamp injection in the gaps between glass glue.
    本文由济南玻璃门安装公司整理发表提供,详情请关注公司网站:http://www.jnjqjc.com/