• 济南慧杭门业有限责任公司
  • 联系人:张经理
  • 手机:15966334566
  • 地址:济南市工业南路106号
  • 网址:http://www.jnjqjc.com
新闻中心当前位置:首页-新闻中心
    卷帘门电机的正确运用
    来源:http://www.jnjqjc.com   时间:2016-8-17 16:46:30
    卷帘门电机的正确运用,下面小编为您介绍一下:
    Rolling door of the correct use of the motor, the following small series for you to introduce:
    1、电机工作环境应保持干燥,电动机外表应保持清洁,进风口不应受尘土、纤维等阻止。
    1, the motor working environment should be kept dry, motor appearance should be kept clean, air inlet should not be dust, fiber, etc.
    2、当电动机的热保护接连发作动作时,应查明问题来自电动机的超负荷运行或热保护设备设定值太低,消除故障后,方可投入运转。
    2, when the motor thermal protection of successive attacks, the problem should be identified from the motor overload operation or thermal protection equipment set value is too low, to eliminate the fault, the party can be put into operation.
    3、应保证电动机在运转的润滑,通常的电动机运转 5000 小时左右,即应弥补或替换 光滑脂运转中发现轴承过热或光滑蜕变时,液压 及时换光滑脂。替换光滑脂时,应铲除旧的光滑油,并有汽油洗净轴承及轴承盖的油槽,然后将 ZL-3锂基脂 填充轴承内外圈之间的空腔的 1/2 对 2 极)及 2/3 对4 6 8 极)。
    3, the motor should be guaranteed in the operation of lubrication, usually running 5000 hours or so, that should make up or replace the smooth operation of the smooth operation of the bearings found when the overheating or smooth transformation of the hydraulic. Replace smooth fat should be to eradicate the old smooth oil, and gasoline to clean the bearing and bearing cover of the oil tank, and then the zl-3 lithium grease filling of the cavity between the inner ring and the outer ring of the bearing 1 / 2 to 2 pole) and 2 / 3 of 4 6 8 poles).
    4、当轴承的寿命终了时,电动机运转的振荡及噪声将显着增大,查看轴承的径向游隙抵达下列值时,即应替换轴承。
    4, when the end of the service life of the bearing, motor running vibration and noise will significantly increase, check the radial clearance of the bearings arrived the following values, which should replace the bearing.
    5、设备电动机时,从轴伸端或非伸端取出转子都能够。若是没有必要卸下电扇,仍是从非轴伸端取出转子较为便当,从定子中抽出转子时,应防止损坏定子绕组或绝缘。
    5, when the device motor, the rotor can be removed from the shaft extension or extension ends. If there is no need to remove the fan, or from the non shaft extending end out rotor is more convenient, from the stator in out of the rotor should be to prevent damage to the stator winding insulation.
    6、替换绕组时有必要记下原绕组的办法,尺度及匝数,线规等,当丢失了这些数据时,应向制作厂讨取,随意更改原描绘绕组,常常使电动机某项或几项功用恶化,乃至于无法运用。
    6, replace winding when necessary to set down the primary winding way, scale and number of turns, wire gauge, etc, when the loss of these data should be to the production factory, please take, arbitrarily change the original which depicts the winding, often make motor one or several function deterioration, and cannot be used.
    相信看了上面的介绍,您定会心动,要了解更多的卷帘门内容,欢迎您进店或电话咨询更多信息,期待您的到来。
    I believe that the introduction of the above, you will be moved, to understand more about the contents of the door, you are welcome to enter the shop or telephone for more information, look forward to your arrival.