• 济南慧杭门业有限责任公司
  • 联系人:张经理
  • 手机:15966334566
  • 地址:济南市工业南路106号
  • 网址:http://www.jnjqjc.com
新闻中心当前位置:首页-新闻中心
    无框玻璃门的安装步骤
    来源:http://www.jnjqjc.com   时间:2016-10-26 10:20:24
    无框玻璃门区别于铝合金门、塑钢门等普通门大的特点,是它的门扇(玻璃)周边没有固结的边框。下面小编讲解一下它的安装步骤。
    The difference in characteristics of frameless glass doors Aluminum Alloy door, steel door and other common door is its largest, the door leaf (glass) border surrounding no consolidation. The following small series to explain about its installation steps.
    1、固定隔墙的安装均应在室内处其它工序施工基本完成后进行。固定玻璃隔断及活动玻璃门扇必须统一放线定位,按设计图要求放出隔断及玻璃门的定位线,确定门框位置,准确地测量地面标高及门框顶部标高。
    1, the installation of the fixed partition should be in the interior of the other working procedures after the completion of the completion of the basic. Fixed glass partition glass door and activities must be unified line positioning, positioning line according to the design requirements from partition and glass doors, determine the frame position, accurate measurement of surface elevation and the elevation of the top of the door frame.
    2、安装玻璃隔墙、门顶部限位槽的宽度应大于玻璃厚度2~4mm,槽深在20~30mm之间,以便注胶。安装方法可由所弹中心线引出两条金属装饰板边线,然后按边线进行门框顶部限位槽的安装。槽口内的木垫板是调整槽深的。通过垫板的增多或减少调整。
    2, the installation of glass partition wall, door width of the top limit of the glass should be greater than the glass thickness of 2 ~ 4mm, the groove depth between 20 ~ 30mm, so that the glue injection. The installation method of two metal decorative plate line by the elastic center line extraction, and then press the edge of door frame top limit groove installation. Notch wood plate is adjusting the groove depth. Through the pad increase or decrease adjustment.
    3、安装金属饰面的木底托。安装方法可在原预埋木砖上钉方木,或通过膨胀螺栓钉方木,把方木固定在地面上,然后再用万能胶将金属饰面板粘在木方上。铝合金方管,可用铝角固定在框柱上,或用木螺钉固定在埋入地面中的木砖上。
    3, the installation of metal decorative wood base. Installation method in embedded block nail in wood, or through the expansion bolt nail in wood, the wood is fixed on the ground, then the adhesive to metal decorative panel glued on wood. Aluminum Alloy square, available aluminum angle is fixed on the frame column, or with wood screws fixed on the sunken in the grounds.
    4、安装坚向门框。按所弹中心线钉立门框方木,然后用胶合板确定门框柱的外形尺寸和位置的固定(注意应减除装饰面尺寸)。后外包金属装饰面,包时要把饰面对头接缝放置在安装玻璃的两侧中间位置。接缝位置必须准确并保证垂直。
    4, the installation of the door to the door. According to the elastic line nail vertical door frame timbers, and then determine the plywood shape size and position of the door frame is fixed (note should be less decorative surface size). Finally, when the metal decorative surface is outsourced, the butt joint of the butt joint is arranged in the middle position of the two sides of the glass. The seam position must be accurate and guaranteed to be vertical.
    5、玻璃安装。用玻璃吸盘器(或玻璃吸盘机)把厚玻璃吸紧吸住,然后手握吸盘把通过2~3人把厚玻璃板抬起并竖立起来移至安装地点准备就位。就位方法:应把玻璃上部插入门框顶部的限位槽内,然后把玻璃的下部放到底托上对正中心线,并对好两侧门框的安装位置,使厚玻璃的两侧边部正好封住门框的金属饰面对缝口,要求做到内外都看不见饰面接缝口。
    5, glass installation. Use glass sucker (or glass sucker machine) thick glass ceiling tight grip, and then holding the chuck by 2 ~ 3 thick glass plate is raised and erected to installation site preparation in place. Methods: the position limiting groove in the upper part of the glass into the top of the door frame, then put the glass on the lower part of the bottom bracket on the center line, and the installation position of the door on both sides of the good, the metal finishes on the thick glass edge on both sides of the door just seal the mouth, requires both inside and outside the invisible decorative seams export.
    6、玻璃固定。在底托木上的内外钉两根扁方木条把厚玻璃夹在中间,但距厚玻璃板需留出4mm左右的空隙,然后在扁方木条上涂刷万能胶将饰面金属板粘卡在方木和两根扁方木条上。
    6, glass fixed. At the end of the nail and used two flat square batten thick glass in the middle, but from the thick glass to void leaving about 4mm, and then painted on the flat side of wood adhesive to decorative metal plate sticking on square and two flat square timber.
    7、注玻璃胶封口。在顶部根位槽两侧空隙内和底托玻璃槽口的两侧以及厚玻璃与门框柱的对缝处注入玻璃胶。注入顺序应从某一条缝隙的端头开始到末端终止,中途不得停顿。操作要领是:握紧嵌缝枪压柄用力要均匀,同时顺着缝隙移动的速度也要均匀,即随着玻璃胶的挤出,匀速移动注胶口,使玻璃胶在缝隙处形成一条均匀的直线。后用塑料片刮去多余的玻璃胶并用干净布擦去胶。
    7, glass plastic sealing. Support on both sides of glass notch and thick glass and frame column on the injected plastic glass at the top of the root slot and the bottom gap on both sides. The injection order should begin from the end of a gap to the end of the end, and no stop in the middle of it. The operation essentials are: caulking gun grip handle pressing force should be uniform, and the gap along the moving speed should be uniform, with the extrusion of glass glue, moving the glue injecting mouth, make glass glue to form a uniform line at the seams. Finally, use the plastic sheet to scrape off the excess glass glue and use a clean cloth to wipe off the glue.
    8、玻璃之间对接。固定部分的厚玻璃板,由于宽度尺寸过大,必须用两块或两块以上进行拼装而成,两块对齐拼接必然形成接缝,对接缝应留2~3mm的距离(对接缝的玻璃切口必须倒用)。玻璃固定后,要用玻璃胶入缝隙中,注满后同样要用塑料片把胶刮平,使缝隙形成一条洁净的均匀直线,玻璃面上要用干净布擦净胶迹。
    8, glass butt. Thick glass plate fixing part, the width is too large, must be two or more than two were assembled, two pieces of mosaic alignment must form the seams should be 2 ~ 3mm the distance of the joint (on the joint glass incision must be inverted). The glass is fixed, to use glass glue is filled into the gap, to use the same piece of plastic glue scraping, the gap formed a clean uniform, the glass surface with a clean cloth to wipe glue.
    我公司致力于为用户提供值得信赖的优良产品。我们期待与您建立长期的战略合作关系,为您提供优良的质量和完善的服务体系。
    Our company is committed to providing customers with reliable quality products. We look forward to working with you to establish long-term strategic partnership, to provide you with excellent quality and perfect service system.