• 济南慧杭门业有限责任公司
  • 联系人:张经理
  • 手机:15966334566
  • 地址:济南市工业南路106号
  • 网址:http://www.jnjqjc.com
新闻中心当前位置:首页-新闻中心
    济南玻璃门怎么调节缝隙?
    来源:http://www.jnjqjc.com   时间:2017-8-15 14:14:04
    济南玻璃门安装在竖框中的玻璃应在下方设两块承重垫块,搁置点离玻璃垂直边缘的距离为玻璃宽度的l/4且不小于150mm。其他方向应设定位块,以固定玻璃确保四周缝隙均匀。
    Ji'nan glass door is arranged on the frame of the glass should be provided with two pieces of bearing pad on the bottom, aside from the glass vertical to the edge of the glass width l/4 and not less than 150mm. The other direction should be fixed block, to fix the glass, to ensure that the gap around the uniform.

    在安装玻璃时,若没有按规定设置垫块或玻璃下料尺寸偏大,无法安放垫块,使玻璃直接与玻璃槽接触,周边空隙不均,玻璃重量不能得到很好地支撑,严重时造成窗扇变形。造成这种情况的原因是什么:

    济南玻璃门

    When the glass is installed, if not in accordance with the provisions set pad or glass material size is too large, can not be placed so that the glass pad, direct contact with the glass groove and the surrounding space is not uniform, the weight of the glass can not be well supported, caused severe deformation of the window sashes. What is the cause of this situation?:
    1、安装玻璃门时没有及时清除槽口内的杂物,使玻璃与槽口不对中。
    1, the installation of glass doors did not promptly remove the debris in the slot, so that the glass and groove misalignment.
    2、济南玻璃门同玻璃槽口的缝隙不均,橡胶条与玻璃、玻璃槽接触不良,凸出玻璃槽口,用手能轻易地将密封条拉脱。
    2, Ji'nan glass door with glass notch uneven, rubber and glass, a glass groove is bad, convex glass notch, can easily seal off by hand.
    3、在转角处橡胶条未断开,未注胶粘结。
    3, at the corner of the rubber strip is not broken, not injected glue bonding.
    济南玻璃门整改的措施是:
    Ji'nan glass door rectification measures are:
    1、安装济南玻璃门前要认真清除槽口内的杂物,如砂浆、砖屑、木块等,玻璃安放时应认真对中,保证两侧间隙均匀,并及时较正固定,防止碰撞移位,偏离槽口中心。
    1, install the Ji'nan glass door, carefully remove the impurities in the slot, such as mortar, brick, wood chips, glass should be carefully placed on both sides, to ensure uniform clearance, and timely is fixed, to prevent the collision shift, deviating from the center of the notch.
    2、橡胶密封条不能拉得过紧,下料长度比装配长度长2O-3Omm。安装时应镶嵌到位,表面平直,与玻璃、玻璃槽口紧密接触,使玻璃周边受力均匀。在转角处橡胶条应作斜面断开,并在断开处注胶粘结牢固。
    2, rubber seals can not be stretched too tight, the length of the material is longer than the assembly length of 2O-3Omm. Installation should be inserted in place, the surface flat, close contact with glass, glass notch, so that the surrounding glass force evenly. At the corner, the rubber strip should be beveled to open and glue firmly at the break.
    3、用密封胶填缝固定玻璃时,应先用橡胶条或橡胶块将玻璃挤住,留出注胶空隙,注胶深度应不小于5mm,在胶固化前,应保持玻璃门不受振动。
    3, with sealant to fix the glass, should first use rubber or rubber block to squeeze the glass, leaving the glue injection gap, glue depth should be no less than 5mm, in the glue before curing, should keep the glass door from vibration.
    您如果对我们的产品感兴趣或者有任何的疑问,您可以直接给我们留言或直接与我们联络,我们将在收到您的信息后,会时间及时与您联络。
    If you are interested in our products or have any questions, you can either leave us a message or contact us directly. We will contact you in the first time after receiving your information.