• 济南慧杭门业有限责任公司
  • 联系人:张经理
  • 手机:15966334566
  • 地址:济南市工业南路106号
  • 网址:http://www.jnjqjc.com
新闻中心当前位置:首页-新闻中心
    玻璃门定做安装工艺介绍
    来源:http://www.jnjqjc.com   时间:2017-10-7 0:30:57
    1. 施工工艺
    1. construction process
    定位、放线→安装框顶部限位槽→安装金属饰面的木底托→安装竖向门框→安装玻璃→安装玻璃门扇上下门夹→门扇定位安装→安装玻璃门拉手

    Positioning, line, installation box at the top of the limiting groove, the installation of metal decorative wood base, installation of vertical frames, glass installation, installation of glass door gate, door installation, installation positioning clamp glass door handle

    济南玻璃门

    2. 施工方法与技术措施
    2. construction methods and technical measures
    (1) 定位、放线:由固定玻璃和活动玻璃门扇组合在的玻璃门,统一进行放线定位。根据设计和施工图纸的要求,放出玻璃门的定位线,并确定门框位置,准确地测量地面标高和门框顶部标高以及中横框标高。
    (1) positioning and laying out: the fixed glass and movable glass door are combined in the glass door, and the line positioning is carried out uniformly. According to the requirements of the design and construction drawings, release the positioning line of the glass door, and determine the location of the doorframe, accurately measure the floor elevation, the top of the doorframe and the elevation of the middle cross frame.
    (2) 安装框顶部限位槽:限位槽的宽应大于玻璃厚度2-4mm,槽深为10-20mm。安装时,先由所弹中凡线引出两条金属装饰板边线,然后按边线进行门框顶部限位槽的安装。通过胶合垫板调整槽口内的槽深。限位槽除木衬外,采用1.5mm钢板压制、钢板焊制及铝金属型材等衬里外包不锈钢等制成。
    (2) limit slot at the top of the installation frame: the width of the spacing groove should be greater than the glass thickness 2-4mm, and the groove depth is 10-20mm. When installing, first, draw out two metal decorative boards on the inside of the shell, then press the side line for the installation of the groove at the top of the doorframe. Adjust the groove depth in the notch by gluing the backing plate. Except the wooden lining, the spacing groove is made of 1.5mm steel plate pressing, steel plate welding and aluminum metal profile lining, stainless steel and so on.
    (3) 安装金属饰面的木底托:先把方木固定在地面上,然后再用万能胶将金属饰面板粘在木上,方木可采用直接钉在预埋木砖上,或通过膨胀螺栓连接的方法固定。若采用铝合金方管,可以用铝角固定在框柱上,或用木螺钉固定在埋入地面中的木砖上。
    (3) the installation of metal decorative wood base: first, the wood is fixed on the ground, then the adhesive to metal panels bonded to the wood, the wood can be used directly in the nail embedded block, or through an expansion bolt connection method of fixed. If the Aluminum Alloy tube, can use aluminum angle is fixed on the frame column, or with wood screws fixed on the sunken in the grounds.
    我们一直以质量,顾客至上,作为我们的服务宗旨,尽我们大的努力来为您提供满意的服务,我们真诚的欢迎您来本公司视察,选购,希望我们有良好的合作机会,共同创造双赢的局面!
    We have been to quality first, customer first, as our service tenet, try our best to provide you with satisfactory service, we sincerely welcome you to visit the company, to purchase, I hope we have a good opportunity to work together to create a win-win situation!