• 济南慧杭门业有限责任公司
  • 联系人:张经理
  • 手机:15966334566
  • 地址:济南市工业南路106号
  • 网址:http://www.jnjqjc.com
新闻中心当前位置:首页-新闻中心
    玻璃门施工安装工艺介绍
    来源:http://www.jnjqjc.com   时间:2017-11-24 17:36:16
    定位、放线:由固定玻璃和活动玻璃门扇组合在的玻璃门,统一进行放线定位。根据设计和施工图纸的要求,放出玻璃门的定位线,并确定门框位置,准确地测量地面标高和门框顶部标高以及中横框标高。
    Positioning and stringing: fixed glass and movable glass leaf door assembled in the glass door, unified line positioning. According to the requirements of the design and construction drawings, release the positioning line of glass door, and determine the position of the doorframe, accurately measure the elevation of the ground and the top of the doorframe and the elevation of the middle cross frame.
    安装框顶部限位槽:安装时,先由所弹中凡线引出两条金属装饰板边线,然后按边线进行门框顶部限位槽的安装。通过胶合垫板调整槽口内的槽深。限位槽除木衬外,采用1.5mm钢板压制、钢板焊制及铝金属型材等衬里外包不锈钢等制成办公室玻璃隔断。

    Mounting slot at the top of the installation frame: when installing, first, draw out two metal trim lines on the inside of the shell, then install the limit slot on the top of the doorframe according to the sideline. Adjusting groove depth by gluing plate. In addition to the wooden lining, the glass partition is made of 1.5mm steel plate pressing, steel plate welding, aluminum metal profile and other stainless steel lining.

    济南玻璃门维修

    不锈钢楼梯扶手安装金属饰面的木底托:先把方木固定在地面上,然后再用万能胶将金属饰面板粘在木上,方木可采用直接钉在预埋木砖上,或通过膨胀螺栓连接的方法固定。若采用铝合金方管,可以用铝角固定在框柱上,或用木螺钉固定在埋入地面中的木砖上。
    Stainless steel staircase handrail installation metal decorative wood base: first, the wood is fixed on the ground, then the adhesive to metal panels bonded to the wood, the wood can be used directly in the nail embedded block, or through an expansion bolt connection method of fixed. If the Aluminum Alloy tube, can use aluminum angle is fixed on the frame column, or with wood screws fixed on the sunken in the grounds.
    安装竖向门框:接所弹中心线钉立门框方木,然后用胶合板确定门框柱的外形和位置。后外包金属装饰面。包饰面时要把饰面对头接缝位置放在安装玻璃的两侧中门位置。接缝位置必须准确并确保垂直。
    The installation of vertical frames: the elastic line nail vertical door frame timbers, and then determine the shape and position of frame column with plywood. Finally, the metal decorative surface is wrapped. The package finishes to finish butt joint position on the middle position installed on both sides of the glass. Seam position must be accurate and ensure vertical.
    安装玻璃:用玻璃吸盘机把厚玻璃吸紧,然后手握吸盘把由2-3人将厚玻璃板抬起,移至安装位置。然后玻璃上部插入门框顶部的限位槽。然后把玻璃的下部放到底托上。玻璃下部对准中心线,两侧边部正好封住门框外的金属饰面对缝口,要求做到内外都看不见饰面接过口。
    Install glass: suction the thick glass with a glass suction machine, then hold the sucker, lift the thick glass plate by 2-3 people and move to the installation position. Then the upper part of the glass is inserted into the limiting slot at the top of the doorframe. Then put the lower part of the glass on the bottom bracket. The glass bottom is aligned to the center line, metal finishes on the two sides of just outside the door shut, requires both inside and outside the invisible finishes took the mouth.
    以上就是小编为您讲解的有关知识,我们拥有严谨的工作态度,熟练的工作技能,将确保任务准确、高效的完成。
    The above is Xiaobian related knowledge for you, we have a rigorous working attitude, skilled work skills, will ensure that the task is accurate and efficient completion.