• 济南慧杭门业有限责任公司
  • 联系人:张经理
  • 手机:15966334566
  • 地址:济南市工业南路106号
  • 网址:http://www.jnjqjc.com
新闻中心当前位置:首页-新闻中心
    玻璃门装置流程都有哪些?
    来源:http://www.jnjqjc.com   时间:2019-11-25 15:29:27

      现在越来越多的人选择济南玻璃门,但是大家在装置玻璃门的时候就会手忙脚乱,所以现在就由济南慧杭门业有限责任公司告诉大家装置玻璃门都有哪些步骤及过程吧!

      Now more and more people choose Jinan glass door, but everyone will be in a hurry when installing the glass door, so now Jinan Huihang door industry Co., Ltd. will tell you the steps and process of installing the glass door!

      1、 定位、放线

      1. Positioning and setting out

      由固定玻璃和活动玻璃门扇组合玻璃门,统一进行放线定位,依据设计和施工图纸要求,放出玻璃门的定位线,同时确定门框位置。

      The combination of fixed glass and movable glass door leaves shall be used for setting out and positioning. According to the requirements of design and construction drawings, the positioning line of glass door shall be set out and the position of door frame shall be determined at the same time.

      2、 安装框顶部限位槽

      2. Limit slot at the top of the mounting frame

      限位槽的宽应大于玻璃厚度二至四毫米,槽深为十至二十毫米。安装时,一开始由所弹中凡线引出两条金属装饰板边线,接着按边线进行门框顶部限位槽的安装,通过胶合垫板调整槽口内的槽深。

      The width of the limit groove shall be two to four millimeters greater than the thickness of the glass, and the groove depth shall be ten to twenty millimeters. At the beginning of installation, two metal decorative board sidelines are led out from the snapped line, then the top limit slot of the door frame is installed according to the sideline, and the groove depth in the slot is adjusted by gluing the base plate.

    济南玻璃门

      3、 安装金属饰面的木底托

      3. Install wood base bracket with metal facing

      把方木固定在地面上,用万能胶把金属饰面板粘在木上。若采用铝合金方管,可以用铝角固定在框柱上,或用木螺钉固定在埋入地面中的木砖上。

      Fix the square wood on the ground, and glue the metal decorative panel on the wood with the universal glue. If aluminum alloy square tube is used, it can be fixed on the frame column with aluminum angle or on the wood brick embedded in the ground with wood screw.

      4、 安装竖向门框

      4. Install the vertical door frame

      接所弹中心线钉立门框方木,接着用胶合板确定门框柱的外形和位置,最后外包金属装饰面。包饰面时要把饰面对头接缝位置放在安装玻璃的两侧中门位置。

      Nail the square wood of the door frame with the snapped central line, then determine the shape and position of the door frame column with plywood, and finally wrap the metal decorative surface. When covering the finish, the butt joint of the finish shall be placed at the middle door on both sides of the installation glass.

      5、 安装玻璃

      5. Installation of glass

      用玻璃吸盘机把厚玻璃吸紧,把厚玻璃板抬起移至安装位置。先把玻璃上部插入门框顶部的限位槽,再把把玻璃的下部放到底托上。

      Use the glass sucker to tighten the thick glass and lift the thick glass plate to the installation position. First insert the upper part of the glass into the limit slot at the top of the door frame, and then put the lower part of the glass on the bottom bracket.

      6、 固定玻璃

      6. Fixed glass

      在底托方木上的内外钉两根小方木条把厚玻璃夹在中门,在方木条上涂刷万能胶并把饰面金属粘在在方木条上。

      Nail two small square wood strips inside and outside on the bottom supporting square wood to clamp the thick glass in the middle door, brush the universal glue on the square wood strip and stick the facing metal on the square wood strip.

      7、 注玻璃胶封口

      7. Glass glue sealing

      在顶部限位槽和底部托槽口的两侧,以及厚玻璃与框柱的对缝处等各缝隙处,注入玻璃胶封口,用工具刮去多余的玻璃胶。

      At the two sides of the top limit slot and the bottom bracket opening, as well as the butt joint between the thick glass and the frame column, inject glass glue to seal, and scrape off the excess glass glue with a tool.

      8、 玻璃对接

      8. Glass butt joint

      玻璃门固定部分因尺寸过大而需要拼接时,其对缝要有二至三毫米的宽度,玻璃板边要进行倒角处理。

      When the fixed part of the glass door needs to be spliced due to its large size, its butt joint shall have a width of two to three millimeters, and the edge of the glass plate shall be chamfered.

      9、 地弹簧安装

      9. Installation of ground spring

      门扇安装前地面地弹簧与门框顶面的定位销应安装完毕并且必须同轴线,安装时最好用吊垂线检查确保在同一直线上。

      Before the installation of the door leaf, the ground spring and the locating pin on the top of the door frame shall be installed and must be in the same axis. During the installation, it is better to check with the hanging plumb line to ensure that they are in the same straight line.

      10、 安装上下门夹

      10. Install the upper and lower door clamps

      把上下金属门夹分别装在玻璃门扇上下两端,如果门扇高度不够,可在下门夹内玻璃底部垫木夹板条。

      Install the upper and lower metal door clips on the upper and lower ends of the glass door leaf respectively. If the height of the door leaf is not enough, wood splints can be padded on the bottom of the glass in the lower door clip.

      以上就是有济南慧杭门业有限责任公司告诉大家装置玻璃门都有哪些步骤及过程的一些介绍,希望可以帮到你,想要了解更多请点击官网http://www.jnjqjc.com

      The above is the introduction of the steps and process of the glass door installation, which Jinan Huihang door industry Co., Ltd. has told you. I hope it can help you. To learn more, please click http://www.jnjqjc.com