• 济南慧杭门业有限责任公司
  • 联系人:张经理
  • 手机:15966334566
  • 地址:济南市工业南路106号
  • 网址:http://www.jnjqjc.com
新闻中心当前位置:首页-新闻中心
    大家知不知道维修卷帘门小绝招?
    来源:http://www.jnjqjc.com   时间:2019-11-27 16:37:26

    大家应该发现卷帘门有时会出现一点小故障,遇到这种情况不要慌,我们不仅仅要做好日常维护!现在就由济南慧杭门业有限责任公司教大家遇到济南卷帘门故障怎么处理?

      We should find that the rolling shutter sometimes has a little trouble. Don't panic in this situation. We don't just need to do daily maintenance! Now Jinan Huihang door industry Co., Ltd. is going to teach you how to deal with the trouble of rolling shutter door in Jinan?

      1、电动机不动或转速慢

      1. The motor does not move or the speed is slow

      故障原因:一般是济南电动卷帘门线路断路、电机烧损、停止按钮没复位、限位开关动作、负载较大等引起。

      Fault causes: generally, Jinan electric rolling shutter door circuit is open circuit, the motor is burnt, the stop button is not reset, the limit switch acts, the load is large and so on.

      处理方法:检查线路、并接通;更换烧损电机;更换按钮或重复按动几次;拨动限位开关滑块使它脱离微动开关触点,并调整微动开关位置;检查机械部分有无卡阻,若有则消除卡阻清理障碍物。

      Treatment method: check the circuit and connect it; replace the burned motor; replace the button or press repeatedly several times; move the limit switch slider to make it separate from the contact of the microswitch and adjust the position of the microswitch; check whether the mechanical part is blocked, if any, remove the blocking and clean up the obstacles.

    济南卷帘门

      2、控制失效

      2. Control failure

      故障发生的部位及原因:济南电动卷帘门继电器(接触器)触点粘死、行程微动开关失效或触片变形、滑块紧定螺钉松、靠板螺丝松使靠板移位,使滑块或螺母不能随丝杆转动而移动、限位器传动齿轮破损、按钮上、下键卡死。

      Fault location and cause: the contact of Jinan electric rolling shutter door relay (contactor) is stuck, the travel microswitch is invalid or the contact piece is deformed, the fixed screw of the slider is loose, the screw of the backup plate is loose, which makes the slider or nut cannot move with the rotation of the screw rod, the transmission gear of the limiter is damaged, the up and down keys of the button are stuck.

      处理方法:更换继电器(接触器);更换微动开关或触片;紧定滑块螺钉并使靠板复位;更换限位器传动齿轮;更换按钮。

      Treatment: replace the relay (contactor); replace the microswitch or contact pad; tighten the slider screw and reset the backup plate; replace the drive gear of the limiter; replace the button.

      3、手拉链不动

      3. The hand zipper does not move

      故障原因:环形链条堵住十字槽;棘爪无脱离棘轮;压链架卡死。

      Fault cause: the ring chain blocks the cross slot; the pawl does not break away from the ratchet; the chain press frame is stuck.

      处理方法:理顺环形链条;调整棘爪与压链架相对位置;更换或润滑销轴。

      Treatment method: straighten out the circular chain; adjust the relative position of the pawl and the chain pressing frame; replace or lubricate the pin shaft.

      4、电机振动或噪声较大

      4. Motor vibration or noise is large

      故障原因:济南电动卷帘门刹车盘不平衡或断裂;刹车盘无紧固;轴承失油或失效;齿轮啮合不顺、失油或磨损严重;电机电流声或振动。

      Fault cause: Jinan electric roller shutter brake disc is unbalanced or broken; brake disc is not fastened; bearing oil loss or failure; gear meshing is not smooth, oil loss or serious wear; motor current sound or vibration.

      处理方法:更换刹车盘或重新调整平衡;紧固刹车盘螺母;更换轴承;修配电机轴输出端齿轮、润滑或更换;检查电机,如电机坏损则更换。

      Handling method: replace the brake disc or readjust the balance; tighten the brake disc nut; replace the bearing; repair the output end gear of the motor shaft, lubricate or replace; check the motor and replace it if it is damaged.

      以上就是由济南慧杭门业有限责任公司教大家遇到卷帘门故障怎么处理的一些小绝招!希望可以帮到你,想要了解更多请点击官网http://www.jnjqjc.com

      The above is by Jinan Huihang door industry limited liability company to teach you how to deal with the trouble of rolling shutter door! I hope I can help you. To learn more, please click http://www.jnjqjc.com