• 济南慧杭门业有限责任公司
  • 联系人:张经理
  • 手机:15966334566
  • 地址:济南市工业南路106号
  • 网址:http://www.jnjqjc.com
新闻中心当前位置:首页-新闻中心
    济南玻璃门施工方法与技术措施
    来源:http://www.jnjqjc.com   时间:2014-7-21 11:49:39
    (1) 定位、放线:由固定玻璃和活动玻璃门扇组合在的玻璃门,统一进行放线定位。根据设计和施工图纸的要求,放出玻璃门的定位线,并确定门框位置,准确地测量地面标高和门框顶部标高以及中横框标高。
    (1) positioning, pay-off: combination by fixed glass and glass doors in the glass door, unified pay-off positioning. According to the requirements of design and construction drawings, the glass door of the positioning line, and determined the frame position, and accurately measure the ground elevation and frame transverse box in the top level and elevation.
    济南玻璃门:http://www.jnjqjc.com
    Jinan glass door
    (2) 安装框顶部限位槽:限位槽的宽应大于玻璃厚度2-4mm,槽深为10-20mm。安装时,先由所弹中凡线引出两条金属装饰板边线,然后按边线进行门框顶部限位槽的安装。通过胶合垫板调整槽口内的槽深。限位槽除木衬外,采用1.5mm钢板压制、钢板焊制及铝金属型材等衬里外包不锈钢等制成。
    (2) install box at the top of the tank: limit slot width should be greater than the thickness of the glass 2-4 mm, deeply 10-20 mm slot. When installation, first by playing in every line leads to two metal decorative edges, and then the installation of the door frame according to line the top limit slot. Through agglutination plate adjustment slot inside the groove depth. Limit slot in addition to the wood liner, pressed by 1.5 mm steel plate, steel plate welded stainless steel and aluminium profiles such as lining outsourcing, etc.
    (3) 安装金属饰面的木底托:先把方木固定在地面上,然后再用万能胶将金属饰面板粘在木上,方木可采用直接钉在预埋木砖上,或通过膨胀螺栓连接的方法固定。若采用铝合金方管,可以用铝角固定在框柱上,或用木螺钉固定在埋入地面中的木砖上。
    (3) install metal decorative surface wood tap: put the wood on the ground, and then use all-purpose adhesive to metal veneer glued on the wood, the wood can be used directly on the embedded wooden brick, or fixed by the method of expansion bolt connection. If using aluminum alloy square tube, can use aluminum Angle and fixed on the frame column, or use wood screws on sat on a wooden brick in the ground.
    (4) 安装竖向门框:接所弹中线钉立门框方木,然后用胶合板确定门框柱的外形和位置。后外包金属装饰面。包饰面时要把饰面对头接缝位置放在安装玻璃的两侧中门位置。接缝位置必须准确并确保垂直。
    (4) the installation of the vertical frame: connect the harp center line nail doorcase the wood, the position and the shape of the frame column and plywood. The outsourcing metal decorative surface. Package to make act the role of face veneer head joint position on installation in the both sides of the glass door. Must be accurate and to ensure that the vertical seam position.
    (5) 安装玻璃:用玻璃吸盘机把厚玻璃吸紧,然后手握吸盘把由2-3人将厚玻璃板抬起,移至安装位置。然后玻璃上部插入门框顶部的限位槽。然后把玻璃的下部放到底托上。玻璃下部对准中线,两侧边部正好封住门框外的金属饰面对缝口,要求做到内外都看不见饰面接过口。?
    (5) install glass: the thick glass suction with glass sucker machine, and then hand sucker by 2-3 people to raise plate glass, moved to the installation location. Then to insert the upper glass door at the top of the limit slot. Then put the bottom of the glass on tap. Glass bottom on the center line, two sides of metal decoration face outside the sealed doors seam, it both inside and outside of invisible facing took the mouth. ?
    (6) 固定玻璃:在底托方木上的内外钉两根小方木条把厚玻璃夹在中门,方木条距玻璃板面4mm左右,然后在方木条上涂刷万能胶,将饰面金属粘卡在方木条上。
    (6) fixed glass: tap the wood on the inside and outside nail article two small squares in thick glass sandwiched between the door, wood article is apart from the glass panel 4 mm or so, then the article in the wood coating adhesive, the article will finish metal sticking in the wood.
    (7) 注玻璃胶封口:在顶部限位槽和底部托槽口的两侧,以及厚玻璃与框柱的对缝处等各缝隙处,注入玻璃胶封口,注胶时,由需要注胶的缝隙端头开始,顺缝隙匀速灌注,使玻璃胶在缝隙外形成一条表面均匀的直线,用塑料片刮去多余的玻璃胶,并用布擦将胶迹。
    (7) note glass glue sealing: at the top limit slot and the bottom of the both sides of the slot, and thickness of glass and frame columns on the side seam each aperture place, such as injection glass sealing glue, plastic injection, rubber injection by the need to end, the cracks in the suitable aperture uniform perfusion, glass glue in the formation of a uniform surface cracks or straight line, with glass glue, plastic scrape off the excess and sponged the glue mark.
    (8) 玻璃之间对接:玻璃门固定部分因尺寸过大而需要拼接玻璃时,其对缝要有2-3mm的宽度,玻璃板边要进行倒角处理。玻璃固定后,将玻璃胶注入对接的缝隙中。注满后,用塑料片在玻璃板对接缝的两面将胶刮平,使缝隙形成一条洁净的均匀直线,玻璃面上用干净布擦净胶迹。
    (8) : docking between glass door fixed part need Mosaic glass, due to size is too large for the seam should have 2-3 mm width, glass edge chamfering processing. After the fixed glass, the glass glue injection in the aperture of docking. Fill after the use of plastic in the glass on both sides of the seam will be leveling, make form a clean uniform linear aperture, the glass surface with a clean cloth wipe glue mark.
    (9) 活动玻璃门扇安装:门扇安装前,地面地弹簧与门框顶面的定位销应定位安装完毕,两者必须同轴线,安装时用吊垂线检查,确保地弹簧转轴与定位销的中线在同一会直线上。
    (9) glass doors installation: door leaf before installation, the ground floor spring with the dowel pin frame roof should be installed, both must coaxial line, installed with vertical inspection, to ensure that the floor spring shaft and the centerline of the dowel pin in the same line.
    (10) 安装玻璃门扇上下门夹:把上下金属门夹分别装在玻璃门扇上下两端,并测量门扇高度。如果门扇的上下边距门横框及地面的缝隙超过规定值,即门扇高度不够,可在下下门夹内的玻璃底部垫木夹板条。
    (10) to install the glass door leaf and door stopper: put metal door clip, respectively up and down on the glass doors of both ends up and down, and the door leaf height measurement. If the doors on bottom margin the door frame and ground cracks more than specified value, namely the door leaf height is insufficient, can be in the next door folder at the bottom of the glass mat wood plywood.
    (11) 固定玻璃门上下门夹:定好门扇高度后,在厚玻璃与金属上下门夹内的两侧缝隙外,同时插入小木条,轻敲稳实,然后在小木条、厚玻璃、门夹之间的缝隙中注入玻璃胶。
    (11) fixed glass door and the door: after good door leaf height of up and down in the thick glass and metal door folder on both sides of the aperture, insert a board at the same time, tapping stable, then in a small wood, thick glass, door clamp injection in the gaps between glass glue.
    (12) 门扇定位安装:先将门框横梁上的定位销用本身的调节螺钉调出横梁平面2mm;再将玻璃门扇竖起来,把门扇下门夹内的转动销连接件的孔位对准地弹簧的转动销轴,并转动门扇将孔位套入销轴上;始后把门扇转动900使之与门框横梁成直角,把门扇上门夹中的转动连接件的孔对准门框横梁上的定位销,调节定位销的调节螺钉,将定位销插入孔内15mm左右。
    (12) door leaf positioning installation: first, the locating pin on the frame beam with itself out of the adjustable screw bar planar 2 mm; Glass door leaf stand up again, the rotation of the door leaf door folder pin connector of the rotation of the spring pin hole position alignment, and the number of the rotating door leaf will set into the pin shaft; After the beginning of the door leaf rotation 900 at right angles to the frame beam, the door leaf turn the fitting of a hole in the door clip on the door frame beam positioning pin, adjust the adjusting screw of positioning pin, insert the dowel pin hole around 15 mm.
    (13) 安装济南玻璃门拉手;全玻璃门扇上拉手孔洞,一般在裁割玻璃时加工完成。拉手连接部分插入洞口时不能过紧,应略有松动;如插入过松,可在插入部分裹上软质胶带。安装前在拉手插入玻璃的部分涂少许玻璃胶。拉手组装时,其根部与玻璃靠紧密后再按紧固定螺钉,以保证拉手没有松动现象。
    (13) installation door shake handshandle of jinan; Handle holes on the glass doors, general when cut glass processing is complete. Shake handshandle connection part when inserted into the hole not too close, should be slightly loose; Such as insert too loose, can be wrapped in soft adhesive tape in the insert part. Before the installation shake handshandle inserted into the glass part with a small glass glue. Handle assembly, its roots and glass by close again after press tight set screw, in order to keep the handle without loose phenomenon.