• 济南慧杭门业有限责任公司
  • 联系人:张经理
  • 手机:15966334566
  • 地址:济南市工业南路106号
  • 网址:http://www.jnjqjc.com
新闻中心当前位置:首页-新闻中心
    济南玻璃门门扇安装
    来源:http://www.jnjqjc.com   时间:2015-1-4 16:40:12
    1)划线:在玻璃门扇的上下金属横档内划线,按线固定转变销的销孔板和地弹簧的转变轴衔接板。详细操作可参照地弹簧商品装置阐明。
    1) crossed: under the metal rails within crossed in the glass on the door leaf, change the line according to the fixed change pin pin orifice plate and the spring shaft connecting plate. With the operation may refer to the spring device to clarify the goods.
    2)断定门扇高度:玻璃门扇的高度尺度,在裁割玻璃板时应留心包含插人上下横档的装置有些。通常情况下,玻璃高度尺度应小于测量尺度5mm加左釉冬以便于装置时进行定位调理。
    2) concluded that the door height: the height scale glass door, should pay attention to insert on the lower rungs of the device contains some in cutting glass plate. Usually, glass height scale should locate conditioning is less than the measurement scale 5mm plus left glaze winter to facilitate device.
    把上、下横档 别离装在厚玻璃门扇上下两头,并进行门扇高度的测量。假设门扇高度缺乏,即其上下边距门横框及地上的缝隙超越规定值,可在上下横档内加垫胶合板条进行调理。假设门扇高度超越装置尺度,只能由专业玻璃工将门扇剩余有些裁往。
    The lower rungs, were installed in the thickness of the upper and lower ends of the glass door, and the door height measurement. Assuming that the height of the door leaf is lacking, namely the upper and lower from the door gap transverse frame and the ground beyond the specified value, can add mat plywood in the top and bottom rail in conditioning. Assuming that the height of the door leaf beyond the device scale, will only remaining some discretion by professional door to glass industry.
    3)固定上下横档:门扇高度断定后,即可固定上下横档,在玻璃板与金属横档内的两头空地处,由两头一起插人小木条,轻敲稳实,然后在小木条、门扇玻璃及横档之间构成的缝隙中注人玻璃胶。
    3) fixed top and bottom rail: the height of the door leaf to determine, can be fixed on the bottom rail, the glass plate and the metal rails within the two space, by two inserted human small batten, tapping is solid, the gap between the small piece of wood, then the door glass and a crosspiece injection people glass glue.
    4)门扇固定:进行门扇定位装置。先将门E横梁上的定位销自身的调理螺钉调出横梁平面1—2㎜,再将玻璃门扇竖起来,把门扇下横档内的转变销衔接件的孔位对准地弹簧的转变销轴,并转变门扇将孔位套人销轴上。然后把门扇转变90。使之与门框横梁成直角,把门扇上横档中的转变衔接件的孔对准门框横梁上的定位销,将定位销插进孔内15mm左右 。
    The 4 door is fixed to the door): positioning device. The first door E beam positioning pin on the adjusting screw out its beam planar 1 - 2 mm, the glass door leaf upright, to change the pin connection pieces of the hole in the door leaves are alignment spring change the pin shaft, and the transformation of the door leaf will bore one pin shaft. Then the door leaf 90 changes. Which forms a right angle with the door frame cross beam, the door leaf in the rung change connection pieces hole alignment dowels frame beam, the positioning pin is inserted into a hole of about 15mm.
    5)装置拉手:全玻璃门扇上的拉手孔洞,通常是事前订货时就加T好的,拉手衔接有些插进孔洞时不能很紧,应有松动。装置前在拉手插进玻璃的有些涂少量玻璃胶;如若插进过松,可在插进有些裹上软质胶带。拉手拼装时,其根部与玻璃贴紧后再拧紧固定螺钉。
    5) device handle: full glass door handle holes, usually in advance when ordering and T good, handle connection some inserted into the holes should be not very tight, loose. Device handle is inserted into the glass before some painted a small amount of glass glue; if inserted too loose, can be inserted into some wrapped soft tape. The handle assembly, its root and glass tightly and then tighten the fixing screws.
    济南玻璃门:http://www.jnjqjc.com/